5322A Electrical Safety Tester Calibrator

115/230 V ac (50/60 Hz) +10 % / -14 %, with the maximum voltage difference between neutral and protective earth not exceeding 15 V. Operation with power line between -10 % and -14 % has limitations in burden current for voltage outputs. See AC/DC Voltage Calibrator (VLC option) below.

AC mains input: 2 A, 250 V for 230 V, time delay (T2L250 V – 5 mm x 20 mm) 4 A, 250 V for 115 V, time delay (T4L250 V – 5 mm x 20 mm)

RCD input: 3.15 A, 250 V, fast (F3.15H250 V – 5 mm x 20 mm)

Meter amps (A) input: 20 A, 500 V, time delay (F20H500 V – 6.3 mm x 32 mm)

Loop/Line impedance input: 4 A, 500 V, time delay (T4H500 V – 6.3 mm x 32 mm)

Leakage current input: 100 mA, 250 V, fast (F100 mL250 V – 5 mm x 20 mm)

Operating temperature: 18 °C to 28 °C

Calibration temperature (tcal): 23 °C

Temperature coefficient for temperatures outside of tcal ± 5 °C is 0.1 / °C of the specification, for temperatures between 5 °C to 40 °C.

Storage temperature: -10 °C to 50 °C

Storage recovery time: Typically <24 hours at operating temperature

Operating: 3050 m (10 000 ft)

Storage: 12 200 m (40 000 ft)

Mains: IEC 61010-1: Overvoltage category II, pollution degree 2

Measurement: IEC 61010-2-030: 5000 V (not category rated)

International:

• IEC 61326-1: Basic electromagnetic environment
• CISPR 11: Group 1, Class A
  • Group 1: Equipment has intentionally generated and/or uses conductively-coupled radiofrequency energy that is necessary for the internal function of the equipment itself.
  • Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances.

    Emissions that exceed the levels required by CISPR 11 can occur when the equipment is connected to a test object.

Korea (KCC):

• Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and not to be used in homes.

USA (FCC):

• 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.

Passive mode: 60 V ac to 250 V ac rms

Differential mode: 60 V ac to 250 V ac rms

Substitute mode:10 V ac to 250 V ac rms

Active mode (5322A/VLC only)[1]: 50 V ac to 100 V ac rms

Passive mode: ± (0.3% setting + 2 μA)

Differential mode: ± (0.3% setting + 2 μA)

Test uncertainty can be influenced by power line voltage instability

Substitute mode: ± (0.3% setting + 2 μA)

Activ e mode (5322A/VLC only)[1]: ± (0.3% setting + 1 μA)

[1] The Active Mode outputs are synchronized with the ac mains frequency to suppress interference between the calibrator and external noise sources.

Resistance range: 0 Ω to 10 000 Ω

Resolution: 1 Ω

Multifunction Electrical Tester Calibrator with 1.5 kV Resistance

Multifunction Electrical Tester Calibrator with 5 kV High Voltage Resistance Outputs

Calibrator with 1.5 kV Resistance, 600 V Source, Voltage Loop Compensation

Calibrator with 1.5 kV Resistance and 40 kV Probe

Calibrator with 5 kV Resistance, 600 V Source, Voltage Loop Compensation

Calibrator with 1.5 kV Resistance, 600 V Source, Voltage loop Compensation and 40 kV Probe

Calibrator with 5 kV Resistance, and 40 kV Probe

Calibrator with 5 kV Resistance, 600 V Source, Voltage Loop Compensation and 40 kV Probe

High Voltage Resistor Load for 5322A

Rack Mount Kit for 5322A – Sliding

Transit Case for 5322A (without 5322A-LOAD)